S4 A modular alarm system, providing perimeter and ultrasonic interior protection

• Supplied with 2 x single button radio keys, high power audio siren and red status LED
• The system has full, in-built, CDL control to power/switch a vehicle’s CDL system
• Single immobilisation circuit
• Key theft protection facility - only with an optional keypad
• Auxiliary siren or boot release output & armed accessory or total closure output
• Sophisticated programming and diagnostic facility via either the keypad or the CP3 workshop programmer

Security Features

• 2 x single button radio keys (programmable, water and shock resistant with random 66-bit encryption to prevent scanning and code grabbing. Lost or stolen radio keys can be programmed out)
• Perimeter protection circuit for boot and bonnet (negative input)
• Perimeter protection circuit for doors (negative input)
• Closed loop protection circuit (looped wire to protect accessories, trailers, bike racks etc)
• Ignition detection circuit
• Ultrasonic interior protection (base sensitivity adjustable, length of disturbance adjustable and automatically adjust if any movement is detected during the threshold time)
• Single immobilisation circuit (18 amp continuous/30 amp max)
• Manual arm, using the radio key (or programmable auto arm, which automatically arms the system 60 seconds after the last door is shut - adjustable between 1 and 99 seconds. Auto arm can also be programmed to lock the vehicle if required)
• Auto re-arm can be programmed to re-arm the system if a door is not opened within 60 seconds of disarming the system -adjustable between 1 and 99 seconds. Auto re-arm also re-locks the vehicle
• A Key theft protection feature can be turned on to prevent the radio keys automatically de-activating the immobiliser when the alarm system is disarmed. In this mode the system's PIN must also be entered into the keypad before the vehicle can be started. This prevents the theft of a vehicle even with the owner’s keys
• Last trigger identification via the dashboard LED and a record of the elapsed time since the last trigger can be recalled using the keypad or a CP3 workshop programmer
• The total trigger count memory for each individual circuit since the system was installed or the memory re-set is also stored in the system's memory

Convenience Features

• Full central door locking/unlocking control (with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period)
• Armed output (negative 200mA max) or this can alternatively be used as a total closure output (either via holding down the radio key when arming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period)
• Additional siren/pager output (negative 200mA max) or alternatively this can be used as a total open/boot release output (either via holding down the radio key when disarming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period
• Secure ignition PIN override
• Secure PIN override using the keypad
• Silent arm and disarm (audible bleeps can be programmed back on, however this will breach current legislation)
• The last circuit to trigger can be excluded using the keypad
• The vehicle’s battery voltage can be checked using the keypad
• The sensors are excludable using the keypad, ignition or remotely with the optional two button radio key

Personal Safety Features

• Auto lock can be programmed to lock the vehicle at the start of a journey when the ignition is turned on, and then unlock when the ignition is turned off. This can be excluded on individual occasions
• Panic feature switched using the radio key and or an optional internal button

S4 Box Contents

S4 alarm ECU
ECU brackets and fixing screws
S4 alarm installation wiring loom
3-wire accessory wiring loom
Siren with cable incorporating bonnet switch wire
Siren bracket and fixings
Red LED and loom
Two ultrasonic heads, looms and fixings
Two radio keys
Operating instructions and PIN stickers
Certificate of installation
Two Sigma window stickers
Sheet of remaining foil stickers

Optional Accessories

TC2 – 1299/0204

TCL1-104/0304

Sigma S30-Interactive

• Thatcham Category 1 alarm/immobiliser system, providing perimeter and ultrasonic interior protection
• Supplied with 2 x single button radio keys, self powered siren, keypad and tri-coloured status LED
• The system has full, in-built, CDL control to power/switch a vehicle’s CDL system
• Dual immobilisation circuits
• Key theft protection facility
• Auxiliary siren, armed accessory, total closure, interior lamp illumination, headlamp illumination, 2-stage unlock and boot release or remote engine start/stop outputs (separate module required)
• Sophisticated programming and diagnostic facility via either the keypad or a CP3 workshop programmer
• The S30-INTER package also come complete with detailed installation instructions, modified wiring looms and component plugs designed to keep the additional installation time required to a minimum

Security Features

• 2 x single button radio keys (programmable, water and shock resistant with random 66-bit encryption to prevent scanning and code grabbing. Lost or stolen radio keys can be programmed out)
• Perimeter protection circuit for boot and bonnet (negative input)
• Perimeter protection circuit for doors (positive or negative input)
• Closed loop protection circuit (looped wire to protect accessories, trailers, bike racks etc)
• Ignition detection circuit
• Ultrasonic interior protection (base sensitivity adjustable, length of disturbance adjustable, and automatically adjusts if any movement is detected during the threshold time)
• 2 x circuit, passively setting, immobilisation (18 amp continuous/30 amp max)
• Manual arm, using the radio key (or programmable auto arm, which automatically arms the system 60 seconds after the last door is shut - adjustable between 1 and 99 seconds. Auto arm can also be programmed to lock the vehicle if required)
• Auto re-arm can be programmed to re-arm the system if a door is not opened within 60 seconds of disarming the system -adjustable between 1 and 99 seconds. Auto re-arm also re-locks the vehicle
• A key theft protection feature can be turned on to prevent the radio keys automatically de-activating the immobilisation when the alarm system is disarmed. In this mode the system's PIN must also be entered into the keypad before the vehicle can be started. This prevents theft of a vehicle even with the owner’s keys
• Last trigger identification via the dashboard LED and a record of the elapsed time since the last trigger, can be recalled using the keypad or a CP3 workshop programmer
• The total trigger count memory for each individual circuit since the was system installed or the memory re-set is also stored in the system's memory
• Additional plug in single stage sensor socket (see optional accessories)
• Additional plug in dual stage sensor socket and siren pre-warn facility (see optional accessories)
• Secure data linked, self powered siren included

Convenience Features

• Full central door locking/unlocking control (with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period)
• Armed output (negative 200mA max )
• Additional siren/pager output (negative 200mA max)
• Total closure output (via holding down the radio key when arming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period – negative 200mA max
• Total open/boot release output (via holding down the radio key when disarming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period – negative 200mA max)
• Interior lamp illumination output (negative 200mA max)
• Headlamp illumination output (negative 200mA max)
• Secure ignition PIN override
• Secure PIN override using the keypad
• Silent arm and disarm (audible bleeps can be programmed back on, however this will breach current legislation)
• The last circuit to trigger can be excluded using the keypad
• The vehicle’s battery voltage can be checked using the keypad
• The sensors are excludable using the keypad, ignition or remotely with the optional two button radio key)

Personal Safety Features

• Auto lock can be programmed to lock the vehicle at the start of a journey when the ignition is turned on, and then unlock when the ignition is turned off. This can be excluded on individual occasions
• Two stage unlock can be configured to only unlock the driver’s door when the system is disarmed, the remaining doors are only unlocked if the radio key is pressed a second time
• Panic feature switched using the radio key or an optional internal button

Interactive Features

• The Sigma S30 will automatically send a text message directly to your mobile phone when the alarm system is triggered or when the battery level becomes low on the vehicle - unlimited range!
• A GSM tracking package can be added to the product from as little as £29.99 to allow the owner of the vehicle to track the vehicle's movements via an online mapping facility
• Two-way communication with the Text Alert which will allow you to control the unit
• Additional accessories can be interfaced with the Text Alert to allow you to control;

* The central door locking on the vehicle - By sending a text message you will be able to both lock and unlock your vehicle
* Remote immobilisation - Should your vehicle be stolen, by sending a text message to the unit to immobilise the starter circuit, once the vehicle's ignition has next been switched off the engine will be unable to be restarted.
* An additional siren on the vehicle - By sending a text message you will be able to sound an additional siren on the vehicle.

S30 Box Contents
Qty Description
1  S30 alarm ECU
1  Metal connector/relay cover and anti-tamper screws
1  ECU brackets and fixing screws
1  Modified S30 alarm installation wiring loom
1  8-wire accessory wiring loom
1  Multi function keypad and fixings
1  Secure data linked, self powered siren
1  Siren lead with plug with bonnet switch wire
1  Siren bracket and fixings
1  Tri-colour LED and loom
2  Pair of ultrasonic heads, looms and fixings
2  Radio keys
1  Operating instructions and PIN stickers
1  Certificate of installation
2  Sigma window stickers
1  Sheet of remaining foil stickers

With the addition of the Text Alert product
Qty Description
1  Text Alert ECU with a detachable connector
1  Text Alert GSM aerial & screen cleaning wipe
1  Operating instructions, PIN code card & Orange SIM top-up card
1  GSM tracking package registration form

S32 

• Thatcham Category 2 to 1 upgrade alarm system, providing perimeter and ultrasonic interior protection
• Switched from vehicle’s existing OE remote controls
• Supplied with self powered siren, and tri-coloured status LED
• The system has negative lock/unlock outputs to switch negative controlled CDL systems
• Single immobilisation circuit
• Key theft protection facility - only with the optional keypad
• Auxiliary siren, armed accessory, interior lamp illumination and headlamp illumination outputs
• Sophisticated programming and diagnostic facility via the keypad

Security Features

• Switches securely from the vehicle's existing OE remote
• Perimeter protection circuit for boot and bonnet (negative input)
• Perimeter protection circuit for doors (positive or negative input)
• Closed loop protection circuit (looped wire to protect accessories, trailers, bike racks etc)
• Ignition detection circuit
• Ultrasonic interior protection (base sensitivity adjustable, length of disturbance adjustable, and automatically adjusts if any movement is detected during the threshold time)
• Single immobilisation circuit (18 amp continuous/30 amp max)
• Manual arm, using the vehicle’s existing OE remote (or programmable auto arm, which automatically arms the system 60 seconds after the last door is shut - adjustable between 1 and 99 seconds. Auto arm can also be programmed to lock the vehicle if required)
• Auto re-arm can be programmed to re-arm the system if a door is not opened within 60 seconds of disarming the system -adjustable between 1 and 99 seconds. Auto re-arm also re-locks the vehicle
• Key theft protection feature can be turned on to prevent the OE radio keys automatically de-activating the immobilisation when the alarm system is disarmed. In this mode the system's PIN must also be entered into the keypad before the vehicle can be started. This prevents theft of a vehicle even with the owner’s keys
• Last trigger identification via the dashboard LED and a record of the elapsed time since the last trigger, can be recalled using the keypad
• The total trigger count memory for each individual circuit since the system was installed or the memory re-set is also stored in the system's memory
• Additional plug in single stage sensor socket (see optional accessories)
• Additional plug in dual stage sensor socket and siren pre-warn facility (see optional accessories)
• Secure data linked, self powered siren included

Convenience Features

• Negative door locking/unlocking control (with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period)
• Armed output (negative 200mA max )
• Additional siren/pager output (negative 200mA max)
• Interior lamp illumination output (negative 200mA max)
• Headlamp illumination output (negative 200mA max)
• Secure ignition PIN override
• Secure PIN override using the keypad
• Silent arm and disarm (audible bleeps can be programmed back on, however this will breach current legislation)
• The last circuit to trigger can be excluded using the keypad
• The vehicle’s battery voltage can be checked using the keypad
• The sensors are excludable using the keypad or repeated arming

Personal Safety Features

• Auto lock can be programmed to lock the vehicle at the start of a journey when the ignition is turned on, and then unlock when the ignition is turned off. This can be excluded on individual occasions

S32 Box Contents

S32 alarm ECU
ECU brackets and fixing screws
S32 alarm installation wiring loom
6-wire accessory wiring loom
Secure data linked, self powered siren
Siren lead with plug with bonnet switch wire
Siren bracket and fixings
Tri-colour LED and loom
Two ultrasonic heads, looms and fixings
Operating instructions and PIN stickers
Certificate of installation
Two Sigma window stickers
Sheet of remaining foil stickers

Optional Accessories

TC2 – 1299/0204

TUL1-106/0304

Sigma S34-Interactive

• Thatcham Category 2 to 1 upgrade alarm system, providing perimeter and ultrasonic interior protection
• Supplied with 2 x single button radio keys, self powered siren and tri-coloured status LED
• The system has full, in-built, CDL control to power/switch a vehicle’s CDL system
• Single immobilisation circuit
• Key theft protection facility - only with optional keypad
• Auxiliary siren, armed accessory, total closure, interior lamp illumination, headlamp illumination, 2-stage unlock and boot release or remote engine start/stop outputs (separate module required)
• Sophisticated programming and diagnostic facility via either the keypad or a CP3 workshop programmer
• The S34-INTER package also come complete with detailed installation instructions, modified wiring looms and component plugs designed to keep the additional installation time required to a minimum

Security Features

• 2 x single button radio keys (programmable, water and shock resistant with random 66-bit encryption to prevent scanning and code grabbing. Lost or stolen radio keys can be programmed out)
• Perimeter protection circuit for boot and bonnet (negative input)
• Perimeter protection circuit for doors (positive or negative input)
• Closed loop protection circuit (looped wire to protect accessories, trailers, bike racks etc)
• Ignition detection circuit
• Ultrasonic interior protection (base sensitivity adjustable, length of disturbance adjustable and automatically adjusts if any movement is detected during the threshold time)
• Single immobilisation circuit (18 amp continuous/30 amp max)
• Manual arm, using the radio key (or programmable auto arm, which automatically arms the system 60 seconds after the last door is shut - adjustable between 1 and 99 seconds. Auto arm can also be programmed to lock the vehicle if required)
• Auto re-arm can be programmed to re-arm the system if a door is not opened within 60 seconds of disarming the system -adjustable between 1 and 99 seconds. Auto re-arm also re-locks the vehicle
• A Key theft protection feature can be turned on to prevent the radio keys automatically de-activating the immobilisation when the alarm system is disarmed. In this mode the systems PIN must also be entered into the keypad before the vehicle can be started. This prevents the theft of a vehicle even with the owner’s keys
• Last trigger identification via the dashboard LED and a record of the elapsed time since the last trigger can be recalled using the keypad or a CP3 workshop programmer
• The total trigger count memory for each individual circuit since the system was installed or the memory re-set is also stored in the system's memory
• Additional plug in single stage sensor socket (see optional accessories).
• Additional plug in dual stage sensor socket and siren pre-warn facility (see optional accessories)
• Secure data linked, self powered siren included

Convenience Features

• Full central door locking/unlocking control (with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period)
• Armed output (negative 200mA max)
• Additional siren/pager output (negative 200mA max)
• Total closure output (via holding down the radio key when arming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period – negative 200mA max)
• Total open/boot release output (via holding down the radio key when disarming or for a timed period with the ability to adjust the pulse length, to provide a double pulse or adjust the delay period – negative 200mA max)
• Interior lamp illumination output (negative 200mA max)
• Headlamp illumination output (negative 200mA max)
• Secure ignition PIN override
• Secure PIN override using the keypad
• Silent arm and disarm (audible bleeps can be programmed back on, however this will breach current legislation)
• The last circuit to trigger can be excluded using the keypad
• The vehicle’s battery voltage can be checked using the keypad
• The sensors are excludable using the keypad, ignition or remotely with the optional two button radio key

Personal Safety Features

• Auto lock can be programmed to lock the vehicle at the start of a journey when the ignition is turned on, and then unlock when the ignition is turned off. This can be excluded on individual occasions
• Two stage unlock can be configured to only unlock the driver’s door when the system is disarmed, the remaining doors are only unlocked if the radio key is pressed a second time
• Panic feature switched using the radio key and or an optional internal button

Interactive Features

• The Sigma S34 will automatically send a text message directly to your mobile phone when the alarm system is triggered or when the battery level becomes low on the vehicle - unlimited range!
• A GSM tracking package can be added to the product from as little as £29.99 to allow the owner of the vehicle to track the vehicle's movements via an online mapping facility
• Two-way communication with the Text Alert which will allow you to control the unit
• Additional accessories can be interfaced with the Text Alert to allow you to control;

* The central door locking on the vehicle - By sending a text message you will be able to both lock and unlock your vehicle
* Remote immobilisation - Should your vehicle be stolen, by sending a text message to the unit to immobilise the starter circuit, once the vehicle's ignition has next been switched off the engine will be unable to be restarted.
* An additional siren on the vehicle - By sending a text message you will be able to sound an additional siren on the vehicle.

S34 Box Contents
Qty Description
1  S34 alarm ECU
1  ECU brackets and fixing screws
1  S34 alarm installation wiring loom
1  8-wire accessory wiring loom
1  Secure data linked, self powered siren
1  Siren lead with plug with bonnet switch wire
1  Siren bracket and fixings
1  Tri-colour LED and loom
1  Pair of ultrasonic heads, looms and fixings
2  Radio keys
1  Operating instructions and PIN stickers
1  Certificate of installation
1  Sigma window stickers
1  Sheet of remaining foil stickers

With the addition of the Text Alert product
Qty Description
1  Text Alert ECU with a detachable connector
1  Text Alert GSM aerial & screen cleaning wipe
1  Operating instructions, PIN code card & Orange SIM top-up card
1  GSM tracking package registration form

Optional Accessories

The Sigma PIN and Anti Key Theft keypad provides additional functionality to Sigma S-Series alarms.

The keypad is located within the interior of the vehicle and can be mounted directly to the vehicle dashboard or the top of the windscreen.

Installation is also possible in an out of sight location; within the glove box or a suitable storage pocket.

With the keypad installed to a compatible alarm system, the following features are available:

• Easy entry of the Emergency Override PIN. In the event of a remote failure or loss, the alarm system can be dis-armed by entering the user Personal Identification Number via the keypad, instead of using the standard ignition key entry sequence.

• Anti Key Theft protection. The alarm system can be programmed to request a PIN entry before the vehicle can be started. Even after the alarm system has been dis-armed, a correct PIN is required via the keypad before the immobiliser is disabled. This prevents the vehicle being easily stolen, even if the thief has the vehicle keys.

Please refer to a local installer for assistance with these matters.

Compatibility

The following Sigma alarm systems will accept this type of remote:

• SG0
• SG1
• SG1E
• SG2
• SG2E

Programming The Remote

This type of remote control is supplied complete with instructions for coding it to the alarm system.

The procedure requires access to the alarm fuses and also set-up of the alarm functions after programming.

It may be advisable to obtain the assistance of a professional in order to code this remote to your alarm.

The following Sigma alarm systems will accept this type of remote:

• All Remote controlled M-Series Alarms
• SG10
• SG10E
• SG20
• SG20E
• SG30
• SG34
• SG50
• SG60

Programming The Remote

If your alarm system features a keypad showing 0 to 9 and with keys present and the alarm system can be armed and disarmed using either an existing remote or the PIN number then you can purchase a replacement remote as detailed above and code it to your alarm system.

Full instructions are supplied with the remote.

PLEASE NOTE : We are unable to supply PIN numbers for Sigma alarm systems. Please refer to a local dealer for assitance with this matter.

Please refer to a local installer for assistance with these matters.

Compatibility

The following Sigma alarm systems will accept this type of remote:

• M-Series alarms which were originally supplied with this 3 LED style remote.

Programming The Remote

If your alarm system features a keypad showing 0 to 9 and with keys present AND the alarm system can be armed and disarmed using either an existing remote or the PIN number then you can purchase a replacement remote as detailed above and code it to your alarm system.

Full instructions are supplied with the remote.

PLEASE NOTE : We are unable to supply PIN numbers for Sigma alarm systems. Please refer to a local dealer for assitance with this matter.

Please refer to a local installer for assistance with these matters.

Compatibility

The following Sigma alarm systems will accept this type of remote:

• S-Series alarms which were originally supplied with this 3 LED style remote.

Programming The Remote

If your alarm system features a keypad showing 0 to 9 and with keys present AND the alarm system can be armed and disarmed using either an existing remote or the PIN number then you can purchase a replacement remote as detailed above and code it to your alarm system.

Full instructions are supplied with the remote.

PLEASE NOTE : We are unable to supply PIN numbers for Sigma alarm systems. Please refer to a local dealer for assitance with this matter.